Action Figure Case Made to Measure — millimetre-precise for your figure

Acrylic manufactory in Germany for over 20 years

Fully enclosed case in crystal-clear 4 mm acrylic — for figures in their original packaging (MOC blisters) just as much as for loose figures. You set the dimensions to the millimetre, and the blister holder (retaining bracket, single or double frame) comes at no extra charge. From the second case onwards the unit price falls automatically.

Measure the blister · choose a holder · order — in about 3 minutes

Dimensions in millimetres Blister holder at no extra charge Quantity discount from the 2nd case
Vintage He-Man figure on its original card in a crystal-clear Sora acrylic case, seen at an angle

Vintage He-Man in a Sora acrylic case · many more examples further down ↓

Is there a ready-made case for your figure?

For many Masters of the Universe lines there are ready-made cases with fixed dimensions, orderable directly with no configuring. They are built on exactly the same production pattern as the made-to-measure case. Is your line not among them? Then we build the case to your dimensions.

The ready-made cases are listed line by line in our Masters of the Universe collector's world. For any other figure, configure your case to measure.

What a made-to-measure case is built for

Developed for Masters of the Universe collectors — long since in use for many other lines.

Customer photo: vintage Moss-Man on his original card in a made-to-measure Sora case

Customer photo: vintage Moss-Man in a made-to-measure case

MotU — Vintage & Origins MOC

The classic: figures “mint on card” from the eighties or from the Origins line. The case protects card and blister from dust, knocks and fingers — the holder fixes the card in place without any glue.

→ To the MotU collector's world

Customer photo: a The Real Ghostbusters figure by Kenner on its original card in a made-to-measure Sora case

Customer photo: The Real Ghostbusters (Kenner, 1980s) in a made-to-measure case

Other Carded Figures

Star Wars, G.I. Joe, Turtles, WWE, Marvel and anything else that hangs on a card: you set the dimensions freely in millimetres — the case adapts to the packaging, not the other way round.

Customer photo: a shelf with carded MotU figures in Sora cases and, below, a loose skeleton figure in a long acrylic case

Customer photo: a loose skeleton figure in a long acrylic case, carded figures above

Loose Figures & Dioramas

Without a blister holder the case is a fully enclosed display case for the unpacked figure — with accessories or a small base as well. Minimum height 121 mm, maximum 600 mm.

Customer photo: a collector's room with wooden shelves full of Masters of the Universe figures in made-to-measure Sora cases

Customer photo: a whole MotU collection in made-to-measure cases

Whole Collection Lines

A whole wall of MOC figures? Thanks to the quantity discount the unit price falls automatically with every additional unit ordered — same dimensions, one order, one delivery.

Two ready-made MotU Chronicles Cases with He-Man and Skeletor in their window boxes

Two MotU Chronicles Cases from the ready-made range: the same construction, with fixed dimensions

Ready-Made Cases for MotU

For many MotU lines there are proven standard sizes as ready-made cases — orderable directly, with no configuring.

→ To the ready-made cases

Customer photo: Hammond Collection Velociraptor box from Jurassic Park III in a made-to-measure Sora case

Customer photo: Hammond Collection box (Jurassic Park III) in a made-to-measure case, 175 × 65 × 265 mm

Special Requests

Extra-deep packaging, double blisters, unusual formats: if the configurator will not accept a dimension, write to us — a great deal can be solved as a special order.

Note on trade marks: Masters of the Universe®, MotU® and He-Man® are registered trademarks of Mattel. Star Wars, G.I. Joe, Turtles, WWE, Marvel, Ghostbusters, Jurassic Park and all other brands mentioned or shown belong to their respective rights holders. Sora Shop is an independent manufactory for made-to-measure acrylic products and has no business relationship with any of these manufacturers.

Fully enclosed: how the case is built

The case uses the same plug-and-screw construction as our made-to-measure display cases — with one difference: it is not open at the bottom but has a cover panel at the top and at the bottom. Once assembled, the box is closed on all six sides.

The front and back panels are identical. During assembly one of the two panels is left off at first: screw the case together, insert the blister, then slot the last panel into place and screw it down — done. To change the figure you simply unscrew that one panel again; nothing is glued.

Customer photo: Shadow Weaver on her card in an assembled Sora case, seen at an angle, with top and bottom panel
Customer photo: the assembled case at an angle, with top and bottom panel.
The case from behind: the back of the blister card behind the clear back panel
View from behind: the back panel is clear acrylic as well.
Close-up of the top corner of the case: the panels are slotted together and held with small screws
Corner detail: slotted together and screwed, nothing glued.
4 mm crystal-clear acrylic, all sides
16 M2,5 screws per case
6 sides — completely enclosed
approx. 8 working days delivery time

The blister holder: four versions, all at no extra charge

The holder fixes the card of the blister inside the case — no glue, no drilling, purely by means of slotted-in parts in 4 mm acrylic. Which version you choose is a matter of taste; each has its purpose.

Acrylic case without a blister holder: a MotU Chronicles window box stands freely in the case
noneThe box stands freely in the case (MotU Chronicles Case).
Acrylic case with one retaining bracket across the top of a MotU Kids Core card
retaining bracketOne retaining bracket at the top (MotU Kids Core Case).
Acrylic case with single frame, Flying Fists He-Man on the card (MotU Deluxe Case A)
single frameFrame elements all the way round (MotU Deluxe Case A).
Acrylic case with double frame, Terror Claws Skeletor on the card (MotU Deluxe Case A)
double frameCard held between two frames (MotU Deluxe Case A).

The photos show cases from our ready-made MotU range. They are built on exactly the same production pattern as the made-to-measure case: enter the dimensions and the holder of a ready-made case in the configurator and you get exactly that case. On these front views the frames show only as narrow edges around the card; the section drawings below show how the frames hold it.

All four versions cost the same.
VersionHow it worksEffect on the inside dimensions
none The blister is held by the case dimensions alone: you measure the packaging and order the case so that it fits exactly. Also the right choice for loose figures. none — inside dimensions = usable dimensions
retaining bracket
(a single bar at the top)
A single retaining bracket at the top presses the upper edge of the card against the back panel. For blisters with no room for a frame all the way round — it also protects the card from bending. none — inside dimensions = usable dimensions
single frame Four separate frame elements all the way round press the card flat against the back panel. The frame elements sit at the frame gap (standard 1 mm = card thickness) in front of the back panel. none — the frame only holds the card at its edges, so you can measure the blister directly
double frame In addition an outer frame sits directly against the back panel; the card is held at its edges between the outer and the inner frame and does not touch the back panel. usable depth −4 mm — please add 4 mm to your desired depth

Without a holder — section from above

Section through the case: the blister fits exactly, the bubble reaches to just short of the front panel front ← view from above → back panel exact fit: the case dimensions hold the blister

No frame, no retaining bracket: the case is dimensioned so that the blister fits exactly — the card rests against the back panel and the bubble ends just short of the front panel.

Single frame — section from above

Section through the case: frame elements on the inside press the blister card against the back panel front ← view from above → back panel blue: frame elements — card against the back panel

The four frame elements (blue) sit at a 1 mm frame gap in front of the back panel — exactly the thickness of the card. The card is pressed flat against the back panel. The inside dimensions remain fully usable.

Double frame — section from above

Section through the case: the card held between the outer and the inner frame, 4 mm in front of the back panel front ← view from above → back panel yellow: outer frame — card 4 mm in front of it

The outer frame (yellow) sits directly against the back panel, then comes the 1 mm gap for the card, then the inner frame (blue). The card is held only at its edges and sits 4 mm in front of the back panel — add those 4 mm to the depth.

The frame gap — the “Distance to back panel” field in the configurator:

The frame gap is the space between the blister holder and the back panel — it matches the card thickness of your blister and applies to the retaining bracket and to both frames.

leave the field at 0 = standard 1 mm thicker card? → enter 2 mm, for example

Measuring is easy: take the card thickness at an edge with a vernier caliper — or stay with the standard value, which suits the vast majority of blisters.

How to configure your case in 3 minutes

The configurator calculates as you go — you see the price, the outside dimensions and the quantity discount straight away.

Measure the blister

Width, depth and height of the packaging — in millimetres.

Careful: mm, not cm as with the display cases!

Enter the inside dimensions

With the double frame: desired depth + 4 mm.

Choose a holder

None, retaining bracket, single or double frame — all at no extra charge.

Quantity & order

The unit price falls automatically with the quantity. Delivery approx. 8 working days.

Step 1 in detail: measuring the blister

Three values, all in millimetres. Lay the card flat and measure the card itself, then the bubble:

Width and height: the card

Front view of a blister card with dimension lines for the width and the height of the card width height front view: the card lying flat

Measure the card, not the bubble: its full width and its full height.

Depth: the deepest point of the bubble

Side view of a blister card: the depth runs from the back of the card to the deepest point of the bubble card bubble depth seen from the side: front ← → back

Measure from the back of the card to the deepest point of the blister bubble.

Inside dimensions vs. outside dimensions:

You enter the inside dimensions — the space for the figure. Because of the material thickness and the plug-and-screw system the outside dimensions are slightly larger:

outside width = inside width + 14 mm outside depth = inside depth + 8 mm outside height = inside height + 14 mm

The live calculation shows the finished outside dimensions as well — handy when several cases are to stand side by side on a shelf.

Dimension limits

The configurator checks all limits automatically before you can order.
DimensionFromToIn addition
Width40 mm600 mmonly one of width and height may be over 500 mm; above 500 mm a blister holder is no longer possible
Height121 mm600 mm
Depth30 mm300 mmframe gap at most depth − 10 mm
Open the configurator now →

Quantity discount: the unit price falls by itself

Collectors rarely order just one case. That is why the price contains a one-off share of the base costs — it is charged only once per order, no matter how many cases of the same size you order.

You do not have to do anything for it: simply increase the quantity in the configurator and the live calculation immediately shows the reduced unit price. In the basket the order appears as a single line item; the number of units is given as “Quantity … pcs” in the item name.

Customer photo: a whole Masters of the Universe Classics line on their cards in identical Sora cases on a dining table
Customer photo: a whole MotU Classics line in identical cases.

The Sora plug-and-screw system: nothing glued, fully demountable

The case arrives flat-packed as a construction kit — six panels, 16 M2,5 screws with nuts. Assembly takes a few minutes, and because nothing is glued the case can be opened again at any time to change the figure.

By the way: our plug-and-screw system is no passing fashion — we developed it ourselves more than 20 years ago and had it officially registered as a utility model. View the original document as a PDF ↗

Safe shipping Even large numbers of cases travel flat and arrive undamaged.
Open it at any time Unscrew one panel, change the figure, close it again.
Spare parts Every panel and every part of the blister holder can be reordered on its own.
Made in Germany Over 20 years of manufactory experience.
Close-up of the plug-and-screw system on an action figure case: slotted acrylic panels held with small screws

Material and quality

High-grade industrial-quality PMMA acrylic glass — crystal-clear, lightfast, lighter and more impact-resistant than glass.

4 mm panels & blister holder
> 92 % light transmission
M2,5 countersunk screws & nuts
approx. 8 working days delivery time

Important for MOC collectors: UV behaviour

The acrylic glass itself does not yellow and does not become brittle even after years in the light. But: it offers no UV protection for the contents — and printed blister cards from the eighties in particular fade in direct sunlight. So never put MOC treasures in the sun; that applies with and without a case.

Cleaning: a soft cloth, lukewarm water, a little washing-up liquid — or an acrylic glass cleaner. No glass cleaners containing alcohol or ammonia, no abrasives.

What you should know after delivery

Don’t be alarmed: the protective film

When your parcel arrives, the acrylic parts will probably look blue, green, white or even scratched. That is the protective film covering every part on both sides to prevent scratches during production and shipping.

Simply lift the film at one corner with your fingernail — acrylic cannot be scratched by a fingernail. It is best to peel off all the films before assembly; once a case is closed you can no longer reach the inside surfaces.

Protective film being peeled off an acrylic panel, crystal-clear acrylic visible underneath

Assembly instructions

Depending on how your case is equipped, one of the three instruction sheets applies:

With a frame (PDF) → With a retaining bracket (PDF) → Without a blister holder (PDF) →

Made to measure – no right of withdrawal

This item is manufactured individually for you, to the dimensions and options you choose, only after you have placed your order. Under section 312g(2) no. 1 of the German Civil Code (BGB), such custom-made items are excluded from the statutory right of withdrawal; exchange or return is therefore not possible. Please check your measurements carefully before ordering. Your statutory warranty rights in the event of manufacturing faults or transport damage are not affected – see our Right of Withdrawal page for details.

Unsure about dimensions or the holder? We are happy to help.

Write to us with your dimensions and what you would like to display, and we will suggest a suitable configuration.

Price examples: what does a made-to-measure action figure case cost?

The binding price is produced in the configurator from your dimensions and the quantity. For guidance, here are some examples — calculated with the same formula that also determines the price in the basket.

Made-to-measure action figure case — example prices incl. VAT, plus shipping
ExampleDimensions (W × D × H)ConfigurationPrice
Smallest possible case40 × 30 × 121 mm1 case21,00 €
Figure 100 × 60 × 230 mm100 × 60 × 230 mm1 case24,00 €
Figure 160 × 90 × 330 mm160 × 90 × 330 mm1 case30,00 €
Five cases in this size160 × 90 × 330 mm5 cases together105,00 €
Largest possible case600 × 300 × 500 mm1 case90,00 €

All prices incl. VAT, plus shipping (Germany 5,90 €, other countries see Shipping & Payment). Dispatch in about 8 working days. The blister holder (retaining bracket, single or double frame) comes at no extra charge. Prices are for one case unless stated otherwise — from the second case onwards the unit price falls, because the one-off share of the base costs is charged only once per order.

Calculate your own dimensions →

Frequently asked questions about made-to-measure action figure cases

Do I give the dimensions in centimetres or millimetres?

In millimetres — unlike our made-to-measure display cases, which work in centimetres. Action figure packaging often differs by only a few millimetres, hence the finer unit. All dimensions are inside dimensions.

How do I measure my blister correctly?

Lay the card flat and measure the width × height of the card, then take the deepest point of the blister bubble as the depth. Add 1–2 mm of clearance so that the blister slips in comfortably. Exception, double frame: here add a further 4 mm to your desired depth, because the card is held 4 mm in front of the back panel.

Which blister holder is the right one?

That is a matter of taste — all four versions cost the same. None: the case encloses the blister with an exact fit (and is the choice for loose figures). Retaining bracket: a single retaining bracket at the top presses the upper edge of the card against the back panel — good when there is no room for a frame all the way round. Single frame: four frame elements press the card flat against the back panel. Double frame: the card is held at its edges between two frames and does not touch the back panel.

What does the “Distance to back panel” field mean?

That is the frame gap: the space between the blister holder and the back panel in which the card sits. If you leave the field at 0, we make it with the standard of 1 mm — which suits the vast majority of blisters. Only with thicker card do you enter the thickness you have measured, 2 mm for example. The value applies to the retaining bracket just as much as to both frames.

Why do I have to add 4 mm of depth with the double frame?

With the double frame the outer frame (4 mm acrylic) sits against the back panel first, and in front of it, at the frame gap, sits the card. The bearing plane of the blister is therefore 4 mm in front of the back panel — the usable depth is reduced accordingly. So order the desired depth you have measured plus 4 mm. With the retaining bracket and the single frame this is not necessary, as the card rests directly against the back panel.

Do a frame or a retaining bracket make the inside dimensions smaller?

No — with one exception. Frames and retaining brackets only hold the edges of the card; the usable interior for the blister remains the full inside dimension. So you can measure the packaging and enter it directly. The only exception is the depth with the double frame (−4 mm, see above).

How does the quantity discount work?

The price contains a one-off share of the base costs, which is charged only once per order. If you increase the quantity in the configurator, it is spread over all the cases — the unit price falls automatically and the live calculation shows it straight away. In the basket this is a single line item; the number of units is given in the item name.

Are the dimensions inside or outside dimensions?

Always inside dimensions. Because of the material thickness and the plug-and-screw system the outside dimensions are slightly larger: outside width = inside width + 14 mm, outside depth = inside depth + 8 mm, outside height = inside height + 14 mm. The live calculation shows them as well.

How large can the case be?

Width 40–600 mm, depth 30–300 mm, height 121–600 mm. Only one of width and height may be over 500 mm, and above 500 mm a blister holder is no longer possible. For larger special formats it is best to ask us directly.

Can I get to the figure again later?

Yes, at any time. Nothing is glued: the front and back panels are identical, and one of them is only slotted in and screwed down. To change the figure, undo the screws of that one panel, take the panel off, done.

One part is scratched or broken — do I have to buy everything again?

No. Every panel and every part of the blister holder can be reordered on its own — the spare part numbers (20200a–h) are given in the assembly instructions. You will find the spare parts in the spare parts configurator.

Real customer photos from collectors' shelves

No renderings: this is what Sora cases look like at home, made to measure and ready-made alike. A selection from the photos that customers send us after delivery; the gallery currently holds more than 200 pictures of action figures.

All photos were provided to us by Sora customers and published with their consent.

More than just the action figure case

Masters of the Universe: the collector's world

Ready-made cases for practically every MotU line, from Vintage and Origins through to Masterverse.

To the MotU collector's world →

Figures & Pop Culture

Cases and display cases for action figures, Funko Pop!, anime figures, 1/6 figures and statues.

To the collector's world →

Ready-made cases for MotU

For many MotU lines there are proven standard sizes as ready-made cases, orderable directly with no configuring. They are the same cases, just with fixed dimensions.

To the ready-made cases →

Made to Measure Display Case

For statues, dioramas and groups: one case over everything, ideally with a black base as a stage.

To the display case guide →

Display Cabinets & Racks

A compartmented cabinet, ideal when a whole line of loose figures is to stand clearly arranged side by side instead of in many individual cases.

To Display Cabinets & Racks →

Spare parts for Sora cases

Thanks to the plug-and-screw system every component can be reordered on its own, panels and blister holder parts alike.

To the spare parts →

Your price in 3 minutes

Measure the blister, choose a holder, see the price and the quantity discount in real time.
Manufactured in Germany, dispatch in approx. 8 working days.

Configure now →